Snorkel TB66J User Manual Page 65
- Page / 84
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Chapter 9 – Stowing and Transporting
TB66J – 0083740 61
Warning
The potential for an accident increases when the aerial
platform is lifted using improper equipment and/or
lifting techniques. Death or serious injury could result
from such accidents. Use proper equipment and lifting
techniques when lifting the aerial platform.
Know the weight of the aerial platform and the capacity
of the lifting devices before hoisting.
Lifting devices include the hoist or crane, chains,
straps, cables, hooks, sheaves, shackles, slings, and
other hardware used to support the machine.
The empty vehicle weight is stamped on the serial
number placard and is listed in Chapter 2.
The user assumes all responsibility for:
Making sure the equipment used is capable of sup-
porting the weight of the aerial platform.
Making sure all manufacturer’s instructions and
warnings, regulations and safety rules of their em-
ployer and/or any state or federal law are followed.
Use the following procedure to hoist the aerial platform
onto the transport vehicle.
1. Properly stow the aerial platform.
Note
The lifting lugs at the rear of the chassis are farther apart
than those at the front. Rotating the turntable 180° will
place the counterweight at the rear of the chassis. This
will reduce the number of spreader bars needed by one
and sometimes two.
2.
Inspect the lifting lugs (refer to Figure 9.4) to make sure
they are free of cracks, rust and are in good condi-
tion. Have any damage repaired by a qualied service
technician before attempting to hoist the machine.
3. Remove all personnel, tools, materials, or other
loose objects from the platform.
4. Connect the chains or straps to the lifting lugs using
bolted shackles. Hooks that t properly in the lugs
and that have latching mechanisms to prevent them
from falling out under a slack line condition may also
be used.
Do not run the sling cable through the lifting lugs.
Cable damage and/or failure can result from the
cable contacting the sharp corners of the lug.
There is no effective way of putting a corner pro-
tector in the hole of the lug.
5. Use spreader bars of sufcient length to keep the
chains, straps, or cables from contacting the turn-
table or booms.
When using cables, use rigid corner protectors
at any point where the cable contacts on sharp
corners to prevent damaging the cable.
Careful rigging of the spreaders is required to
prevent machine damage.
6. Adjust the length of each chain or strap so the aerial
platform remains level when raised off the ground.
7. Use the hoist or crane to carefully raise and position
the aerial platform onto the transport vehicle.
Securing for Transport
Use the following procedure to secure the aerial platform
on the transport vehicle.
1. Chock the wheels.
2. Remove all personnel, tools, materials, or other
loose objects from the platform.
Figure 9.4 – Lifting Lugs
Rear of Machine
Front of Machine
Lifting Lugs
(One on each side of machine)
Lifting Lugs
- OPERATOR’S 1
- Table of Contents 3
- Chapter 8 – Operation 4
- Chapter 11 – Troubleshooting 4
- Chapter 1 – Introduction 5
- Maintenance 6
- Manual of Responsibilities 6
- Additional Information 6
- Chapter 3 – Specications 7
- Working Envelope 8
- General Specications 9
- Engine Specications 10
- Engine Oil Viscosity 12
- TB66J – 0083740 9 13
- Chapter 2 – Specications 14
- Chapter 3 – Safety 15
- Prestart Inspection 16
- Operation 16
- Electrical System 17
- Hydraulic System 17
- Tip-Over and Falling Hazards 17
- Placards and Decals 18
- Chapter 4 – Safety Devices 19
- Emergency Lowering Knob 20
- Ground Operation Switch 20
- Platform Foot Switch 20
- Guardrails 20
- Lanyard Anchors 20
- Tilt Alarm 21
- Engine Protection Systems 21
- Flashing Light 22
- Light Switch 22
- Engine Oil 24
- Hydraulic Fluid Filter Gauge 24
- Chapter 6 – Controls 25
- Circuit Breaker Reset Buttons 28
- Upper Controls 28
- Machine/Generator Switch 31
- Horn Button 32
- Operator’s Manual 33
- Fan Belt 34
- Air Intake 34
- Fuel Gauge 34
- TB66J – 0083740 31 35
- Cables and Wiring Harness 36
- Tires and Wheels 37
- Emergency Lowering 38
- Lower Control Station 38
- Level Sensor 39
- Sandblast Protection Kit 40
- Structures 40
- Upper Control Station 41
- Emergency 42
- Stop Button 42
- Engine/Emergency 42
- Power Switch 42
- Start Switch 42
- All Motion Alarm 43
- Air Line to Platform 43
- Platform Glazier Package 44
- Platform Control Cover 44
- Right Side 45
- WA R N IN G 46
- DO NOT RIDE IN PLATFORM 47
- WHILE UNIT IS BEING TOWED 47
- Left Side 48
- D A N G E R 49
- 46 TB66J – 0083740 50
- Prestart Inspection Checklist 51
- 48 TB66J – 0083740 52
- Preparing for Operation 54
- Lower Controls 54
- Four Wheel Drive 57
- Gradeability 57
- Percent of 58
- Angle of Slope 58
- Electrical Power Outlet 59
- AC Generator 59
- Dual Fuel 60
- Air Line 60
- Driving Lights 60
- Platform Work Lights 60
- Bump Guard System 61
- Transporting 63
- Tie-Down 64
- Disconnect Plate 64
- Lifting Lugs 65
- Shutoff Valve 66
- Emergency Power System 67
- 66 TB66J – 0083740 70
- 68 TB66J – 0083740 72
- TB66J – 0083740 69 73
- 70 TB66J – 0083740 74
- Bleeder Valve 75
- Fuel Filter 75
- Bleeder Pump 75
- Fuel Line 75
- Appendix A – Glossary 77
- Appendix A – Glossary 78
- Product Warranty 79
Related products and manuals for Special machinery Snorkel TB66J
Special machinery Snorkel TB85J User Manual
(76 pages)
(76 pages)
© 2020, manymanuals.com. All rights reserved. | 1.675 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals